← All guides · Updated on 9 November 2026

Bowditch (compass rule) traverse adjustment, step by step

A closed traverse never closes perfectly: small errors in angles and distances add up. The Bowditch rule, also called the compass rule, spreads the misclosure over the traverse in proportion to the length of each leg. Here is the full method with a worked example.

1. Check and adjust the angles

For a closed loop of n stations, the interior angles must add up to (n − 2) × 180°. The difference is the angular misclosure. If it is within tolerance, give each angle the same correction (misclosure ÷ n, with the opposite sign), then compute the bearings leg by leg from a known starting bearing.

2. Compute departures and latitudes

For each leg of length L and bearing θ: ΔE = L × sin θ (departure) and ΔN = L × cos θ (latitude). For a loop, the sums ΣΔE and ΣΔN should be zero; what remains is the misclosure fE and fN.

3. Linear misclosure and precision

f = √(fE² + fN²), and the precision is 1 / (ΣL / f). Typical requirements range from 1/5,000 for ordinary work to 1/20,000 or better for control surveys.

4. Bowditch corrections

Each leg receives a correction proportional to its length:

cEi = −fE × Li / ΣL and cNi = −fN × Li / ΣL

Add the corrections to the departures and latitudes, then accumulate from the starting station to get the adjusted coordinates. The traverse now closes exactly.

Worked example

A four-station loop starting at A (1,000.000; 1,000.000), with bearings already adjusted:

LegBearingLength (m)ΔEΔNcEcNAdjusted EAdjusted N
A → B32°28′30″116.41462.50698.210+0.004−0.0011,062.5101,098.209
B → C118°13′38″110.99297.793−52.496+0.003−0.0011,160.3061,045.712
C → D207°24′02″107.358−49.407−95.314+0.003−0.0011,110.902950.398
D → A294°05′48″121.493−110.90649.603+0.004−0.0011,000.0001,000.000

ΣL = 456.257 m, fE = −0.014 m, fN = +0.003 m, so f = 0.014 m and the precision is about 1/32,000: well within tolerance.

Bowditch or transit rule?

The Bowditch rule assumes angles and distances have similar accuracy, which is the case with a total station. The transit rule distributes corrections in proportion to |ΔE| and |ΔN| instead, and suits traverses where angles are much more precise than distances. Least squares is the rigorous method for networks.

Do it online

The traverse calculator handles closed traverses between two known points, loops and open traverses, in degrees or grads: angular and linear misclosure, precision 1/N, Bowditch adjustment and final coordinates, with CSV and DXF export.

Frequently asked questions

What is a good traverse precision?

It depends on the specification. 1/5,000 is common for detail and boundary work, 1/10,000 to 1/20,000 for engineering control, better for geodetic control.

What if the misclosure is large?

Do not adjust it: look for a blunder. Typical causes are a wrong angle unit (degrees vs grads), an angle read in the wrong direction, a forgotten station or a slope distance not reduced to horizontal.

Can I adjust an open traverse?

No. Without a closing point or bearing there is nothing to compare with, so errors cannot be detected or distributed. Always close on a known point when you can.

Open the traverse calculator

Related guides

Whole circle bearing and distance from coordinatesMeasure the area of a piece of land on a satellite mapPlot survey coordinates from Excel into AutoCAD (with names and Z)