Home › Survey calculations › Traverse

Traverse calculation with misclosure and adjustment

Enter your stations, your horizontal angles and your distances: the tool carries the bearings forward, computes the angular misclosure and the linear misclosure, the precision of the traverse, then adjusts the angles and coordinates. Traverse closed between two known points, looped on itself or open.

Angles
Decimal
Type
Start
Start point (known)
Orientation
Backsight reference

You know the bearing of the first side? Enter it and put 0 as the angle on the first line.

End
End point (known)
Orientation
Forward reference
Stations, angles and distances

First line: the starting point. Last line: the closing point (its angle is used for the angular closure, without a distance). The angle at each station is measured clockwise, from the backsight to the foresight: forward reading − back reading. In a loop travelled anticlockwise, these are the interior angles.

Tolerances (optional)

Enter the tolerances from your specifications: the result shows ✓ or ✗.

Result

How to use the calculator

  1. Choose the type: closed between two known points, loop (back to the start) or open.
  2. Start: the known point and its orientation, by a known reference point or by a known bearing.
  3. End (framed): the known closing point and its forward reference, for the angular closure.
  4. Table: one line per station, from start to end, with the measured clockwise angle and the horizontal distance to the next station. Paste your field book from Excel.
  5. Read the misclosures, then export the adjusted coordinates as CSV, TXT or DXF.

Calculation steps

  1. Starting bearing G₀ = bearing of the starting point to its reference.
  2. Carrying the bearings : Gi,i+1 = Gi−1,i + 200 + αi (modulo 400 gon), with α the clockwise angle from the backsight to the foresight. At the start, G = G₀ + α₀.
  3. Angular misclosure fα = computed closing bearing − known bearing. Each angle gets the correction −fα / n.
  4. Provisional coordinates: ΔX = D × sin G, ΔY = D × cos G for each side.
  5. Linear misclosure : fx = ΣΔX − (Xend − Xstart), fy likewise, fl = √(fx² + fy²), precision = ΣD / fl.
  6. Adjustment proportional to the lengths, then final coordinates.

Example: traverse closed between known points

Start A (486,300.000; 362,200.000) oriented on RA (486,180.000; 362,410.000); end B (486,720.150; 362,262.440) oriented on RB (486,905.000; 362,120.000); three intermediate stations S1, S2, S3 and 473 m of traverse.

StationAngle (gon)Distance (m)Adjusted XAdjusted Y
A93.4973117.355486,300.000362,200.000
S1254.0706120.580486,395.421362,268.310
S2148.1351116.912486,512.877362,241.052
S3261.2560118.148486,610.237362,305.772
B217.8910–486,720.150362,262.440

Angular misclosure +3.7 mgon, i.e. −0.74 mgon per angle; linear misclosure 1.1 cm (fx = 1.0 cm, fy = 0.5 cm); precision 1/41,397. Tap Example to find this calculation; first choose “Loop (closed)” for an example of a five-vertex loop.

An abnormal misclosure almost always comes from an input error: angle unit (grads or degrees), angle measured in the wrong direction, forgotten station or unreduced slope distance. The diagram helps spot the faulty station.

Frequently asked questions

How do you calculate the angular misclosure of a traverse?

The starting bearing is carried from station to station: G(next) = G(previous) + 200 + angle (in gon, modulo 400). At the end, the computed bearing of the reference is compared with its known bearing: the difference is the angular misclosure fα. For a loop, you can also compare the sum of the interior angles with (n − 2) × 200 gon.

How is the adjustment done?

The angular misclosure is shared equally over all angles (−fα / n). Then the misclosures fx and fy on the coordinates are distributed in proportion to the side lengths: cX = −fx × D / ΣD and cY = −fy × D / ΣD (Bowditch adjustment).

What is the 1/N precision of a traverse?

It is the ratio between the total length of the traverse and the linear misclosure fl = √(fx² + fy²). A precision of 1/20,000 means 1 cm of error for 200 m travelled. It is compared with the tolerance required by the specifications.

What is the difference between a closed, loop and open traverse?

A traverse closed between known points starts from a known point and ends on another known point, oriented at both ends: it is the safest. A loop returns to its starting point. An open traverse closes on nothing: its errors are not detected, so avoid it except for a few points.

Your computed points can go on the map: tap Copy, open the map tool, then Search for a place → By X, Y coordinates → Several points? Paste a list. You see them on the satellite image and export them as DXF, KML or KMZ.

Other survey calculations

Useful guides

Updated on 31 October 2026. Calculations run in your browser: your coordinates are not sent to our servers.